NEWS
News banner
News & Events
20 May 2026
Content
The rapid development of elastocaloric cooling has created growing demand for high-performance elastocaloric materials. An ideal elastocaloric material should combine a large adiabatic temperature drop with exceptional cyclic stability. However, existing elastocaloric shape-memory alloys (SMAs) typically exhibit either a modest temperature change or insufficient cyclic stability. Combining a large temperature drop with ultrahigh stability therefore remains an unresolved challenge.
Grain-size engineering may help overcome this performance trade-off. Coarse-grained SMAs exhibit poor transformation reversibility and accumulate dislocations and retained martensite during stress-induced transformations. These defects suppress the temperature drop below its theoretical value and compromise cyclic stability. Grain refinement increases resistance to dislocation activity and limits retained-martensite accumulation, potentially improving both properties. Moreover, nanocrystalline structures can improve lattice compatibility across the austenite–martensite interface, further enhancing stability.
Excessive grain refinement, however, causes grain boundaries to constrain the transforming matrix too strongly, substantially increasing the transformation stress. A greater applied stress is then required to drive the transformation, activating additional dislocation motion and ultimately reducing stability. Systematic investigation is therefore needed to identify an optimal grain size that simultaneously delivers a large temperature drop and high cyclic stability.
NiTiCuCo exhibits a lower intrinsic transformation stress and better lattice compatibility than NiTi. Accordingly, NiTiCuCo was selected for this study. Samples with grain sizes of 150 μm, 42 nm and 70 nm were fabricated through high-pressure torsion and subsequent heat treatment.
The coarse-grained 150 μm sample exhibited a maximum room-temperature temperature drop of 18.5 K. However, like other coarse-grained NiTi-based SMAs, it had a low yield strength of only 540 MPa, indicating weak resistance to dislocation activity. Consequently, the material underwent pronounced functional degradation. After 10,000 cycles under a compressive stress of 400 MPa, its temperature drop decreased to only 6 K.
Grain-boundary strengthening increased the yield strength of the 42 nm sample substantially, reaching 2,150 MPa and markedly improving its cyclic stability. Its stability exceeded that of the 150 μm sample during high-stress cycling at both 900 and 1,500 MPa. Performance under 900 MPa was particularly attractive for practical applications. The temperature drop reached 19.5 K and decreased by only 1.5 K after 10,000 cycles.
Nevertheless, the grains in this sample were excessively fine. The resulting grain-boundary constraint increased the transformation stress to 537 MPa. Consequently, a high applied stress was required to drive the transformation, which is unfavorable for long-term stability and practical deployment.
To further optimize performance, the authors prepared a sample with slightly larger grains of 70 nm. The weaker grain-boundary constraint reduced the transformation stress to 370 MPa, allowing the material to operate under applied stresses as low as 500 MPa. At this stress, the sample produced a temperature drop of 21 K without degradation after ten million compressive cycles, demonstrating exceptional operational durability.
This work, entitled “Achieving Large Room-Temperature Elastocaloric Effect and Ultrahigh Cyclic Stability by Grain Size Engineering,” was published in Acta Materialia, a leading journal in metallic materials research. The corresponding authors are Chair Professor Qing-Ping Sun and Research Assistant Professor Qiao Li of the Hong Kong University of Science and Technology, together with Professor Peng Hua of Harbin Institute of Technology, Shenzhen. Dr Hongyang Lin, a postdoctoral researcher at the Hong Kong University of Science and Technology, is the first author.
Read more
6 Mar 2026
Content
Prof. Tso, SEE’s Associate Dean (Internationalisation and Outreach), has been promoted to Chair Professor with the title of Chair Professor of Energy and Sustainability. He has recently received widespread recognition for his pioneering research in fundamental heat transfer, thermal management, indoor built environments and optics for energy-efficient and sustainable technologies and advanced engineered materials. His work includes innovative passive radiative cooling and smart windows solutions as passive building envelopes to reduce energy consumption and enhance building sustainability. Major honours include the NSFC Excellent Young Scientist Fund (Category B, 2025), the Hong Kong Engineering Science and Technology Award (2024–25), the iCANX Young Scientist Award (2025), the RGC Research Fellowship (2024), the HKIE Grand Award (2024) and the TERA Gold Award (2023). Prof. Tso has also been listed the world’s top 2% most highly cited scientists by Stanford University since 2020, underscoring his global impact. Beyond these distinctions, he leads the FIRST Programme (Fostering Innovation for Resilience and Sustainable Transformation), which UNESCO endorsed in 2025 as part of the UN Science Decade. Prof. Tso is a young fellow or member of numerous professional bodies: including the Hong Kong Academy of Engineering (YFHKEng), the Institute of Measurement and Control (FInstMC), the Hong Kong Young Academy of Sciences (YASHK), the Hong Kong Institution of Engineers (MHKIE), the Chartered Institution of Building Services Engineers (MCIBSE), the Institution of Mechanical Engineers (MIMechE), the International Society of Indoor Air Quality and Climate (MISIAQ), the Hong Kong Green Building Council (MHKGBC), the Hong Kong Research Grants Council Research Fellow Alliance (MHKRFA), and the American Society of Mechanical Engineers (MASME). He is also a Chartered Engineer (CEng) and a Registered Professional Engineer (RPE).
Read more